[Features/Advantages]
1. Good adhesion after forming a network structure between molecules after curing
2. After the product is cured, the glue layer is crystal clear.
3. high gloss
4. low smell
5. the stimulation is small, convenient construction operation;
6. high bonding strength
7. strong adhesion
8. excellent aging resistance
9. the rubber layer is good for yellowing resistance
10. the product meets the GB18583 standard, the EU ROHS directive standard, is a green product

[Scope of application]
Mainly used in various types of stone (marble, limestone, granite, sandstone) back glass fiber mesh reinforcement operation.

【Steps for usage】
1. The plate is heated or ventilated to remove moisture;
2. Use a brush or a rag to remove dust, scum and other impurities from the surface of the stone;
3. Evenly spread the glass fiber mesh on the surface of the stone slab;
4. Mix the rubber in a ratio of A:B=2:1 (weight ratio) and mix well;
5. Pour the glue to the surface of the stone, scrape the glue with a squeegee knife, and apply the glue evenly on the surface of the stone, so that the glass fiber mesh is completely wetted by the glue and pasted on the surface of the stone slab;
6. under normal temperature conditions, generally should be in the next step after the adhesive layer is cured for 24 hours;

【Precautions】
First, when dispensing glue:
1. The proportion of glue adjustment must be accurate, and the glue must be mixed evenly;
2. Do not mix the glues of components A and B. Do not put the remaining glue after mixing back into the original packaging;
3. the glue should be used now, after the glue must be used up within the available time;
4. If the glue that exceeds the usable time has a fever, it should be stopped.
5. If the temperature is 25~30 °C, 600g of glue must be used within 5 minutes;
6. The more the amount of glue is adjusted, the higher the temperature, the shorter the time that can be used, and the longer the time is;
7. If the amount of one-time adjustment is too large, it should be used separately and quickly;
8. Do not cover the cover of components A and B. Please cover the cover at any time to avoid absorbing moisture from the air and falling into dust.
9. It is recommended to use a flatware to adjust the glue. When the temperature is high, it is better to use a cooling method to adjust the glue, which can extend the use time;
10. According to the actual situation, an appropriate amount of stone powder can be added to the glue.

Second, when scraping glue:
1. If the conditions permit, the stone can be heated to 40-50 ° C and then glued. Generally, the reference amount of the glue is 100-200 g/m2.
2. stone surface treatment agent, non-epoxy adhesives and other chemicals should not be applied or infiltrated into the stone bonding surface, otherwise it is not suitable for recoating the surface glue.
3. the stone surface has major defects, such as the soil layer should be removed first, and then take the glue and the right amount of stone powder to mix and repair the defects, after the glue is cured, then brush the rubber back mesh.

Third, when curing:
1. If the conditions permit, the glued sheet can be heated to 40-50 ° C, and after 2-3 hours, it can enter the next process;
2. Before the glue is cured, the plate should be placed in a flat position and cannot be stacked. After initial curing, a lubricant such as talc may be applied to the surface of the plate so that the plates are not bonded together when stacked.

【Technical parameters】

【Package Storage and Transportation】
1. The product is sealed and stored in a cool, dry and ventilated warehouse. The storage temperature is 5-40 °C. The product has a shelf life of one year from the date of production. It can be used after the expiration of the inspection.
2. This product is a corrosive product. It is kept away from heat and fire during transportation to prevent sun and rain. It should be handled gently during transportation, loading and unloading, and it is forbidden to roll, impact, press, invert and side.
3. Packing specification: 600kg/group, component A is packed in 200L iron drum, component B is packed in 200L plastic drum; 30kg/group, component A is 10L square white barrel, component B is 10L square blue barrel.

[Questions]
There are many reasons for the unfavorable bonding effect. Please note:
1. The plate is not dry enough or the air humidity is too high, and the moisture content of the plate causes the water content of the plate to be high;
2. The glue A/B component is not adjusted according to the specified ratio;
3. leaving a dead angle when stirring or insufficient mixing time leads to uneven mixing of the glue;
4. The combination of the two components of A and B causes the curing reaction to occur early;
5. After the glue is evenly mixed, it is not used within the effective time.
6. When the temperature in winter is low, the product may crystallize and agglomerate. It can be used after heating and melting the glue without affecting performance.
7. The glue that is not fully cured on the skin and clothes can be wiped clean with cloth dampened alcohol before uncured, and then washed with soapy water; if it accidentally enters the eyes, rinse with plenty of water, then immediately treat it; if inadvertently swallowed, Do not induce vomiting, drink plenty of egg whites or milk, and seek medical attention immediately.

【Protective measures】
Due to the individual differences of the operators, the glue may cause allergies to certain parts of the skin, but the product meets the national mandatory standard of GB18583-2008, which is an environmentally friendly product and has no other harm to the human body. It is recommended that your company use the following necessary protection when using the compound glue:
1. Use in a well ventilated environment;
2. Equipped with necessary protective clothing, protective gloves and protective masks;
3. To avoid direct contact with the skin, if you accidentally contact the skin, you can use soapy water to clean;
4. Before adjusting the glue, first open the cover of component B, let the free low molecular substances volatilize, and then take the glue and adjust the glue;
5. If there is an allergic reaction, employees should change jobs.

【important hint】
1. Due to the ever-changing material of the material to be bonded, material changes may affect the bonding effect. For this reason, be sure to try it before using it in large quantities.
2. Our company solemnly promises that the company's products are produced strictly in accordance with the company's standards. Our company is only responsible for the products themselves and is not responsible for the customer's use of the process.
3. Our company strictly implements the ISO9001 quality system and the ISO14001 international environmental certification system to provide customers with quality and qualified products. The technical opinions provided by our company, whether verbally, in writing or on the experiment, are sincere, but not guaranteed. Users should read the instructions and use the experiment to verify the suitability of the proposed process and use.
4. The company is unable to control the storage and transportation, the environment at the time of use, and the operation process during use. Therefore, the quality problems caused by improper construction of the customer and the associated losses are the responsibility of the user, and it is not the responsibility of the company.
5. No employee of the company has the right to change or waive the above terms!